再次簡單評價
研究生學術計劃
時間/年：2010/2011
模式：數字信號處理 UG3
評估題目：DSP原則，基于MATLAB的系統和補充
評估標記：CWK1
學校：計算機，通訊和網絡
模式合作伙伴：P.Kanda
評估細節和提綱：見網頁信息
Re-assessment Brief

Undergraduate Programme
Academic Year 2010/2011

Module: DIGITAL SIGNAL PROCESSING UG3
Assessment Title: DSP principles, systems and implementation using MATLAB.

Assessment Identifier: CWK1

School: Computing, Telecommunications and Networks
Module Co-ordinator: P.Kanda
Assessment Details
and Deadlines: See ECMS My Course on the intranet.
Brief Assessment Details  Assessment focuses on fundamental principles and algorithms that are used in DSP systems and their implementation using MATLAB.

 
IMPORTANT STATEMENT

Plagiarism:  the presentation of the work of another (from whatever source: http://www.400190.com/Essay_Writing/ book, journal, internet etc) as if it were one’s own independent work.  This can be anywhere on a continuum ranging from sloppy paraphrasing to verbatim transcription without crediting sources.

You are advised to refer to the Student Handbook on matters of cheating and plagiarism as they relate to coursework, group assignments, class tests and examinations.  Both cheating and plagiarism are totally unacceptable and the University maintains a strict policy against them.  It is YOUR responsibility to be aware of this policy and to act accordingly.

The University requires that the following statement is included in all module documents.

“You are reminded of the University Disciplinary Procedures which refer to cheating.  Except where the assessment of an assignment is group-based, the final piece of work which is submitted must be your own work.  http://www.400190.com/Economics/2662.html Close similarity between assignments is likely to lead to an investigation for cheating.  It is not advisable to show your completed work to your colleagues or to share and exchange disks.

You must also ensure that you acknowledge all sources you have used.  Work which is discovered to be the result of collusion or plagiarism will be dealt with under the University’s Disciplinary Procedures, and the penalty may involve the loss of academic credits.

If you have any doubts about the extent to which you are allowed to collaborate with your colleagues, or the conventions for acknowledging the source you have used, you should first of all consult module documentation and, if still unclear, your module tutor.”

You will be asked to confirm in writing when handing in any piece of assessed work that it is your own by completing the Coursework Submission & Record Form which should be printed from ECMS My-course on https://mytid.bcu.ac.uk/#p#分頁標題#e#.

It is the STUDENT’S responsibility to accurately complete the form and comply with its rules and guidance as described in the student handbook for this academic year.
 

Learning Outcomes to be Assessed:

1. Demonstrate an understanding of the properties and characteristics of digital signals and 
    digital signal processing systems.
2. Use mathematical modelling and simulation tools for the analysis of basic and complex digital
    signal processing algorithms.
3.  Apply and evaluate digital signal processing techniques for real-time signal conditioning.
4.  Design and implement the digital signal processing algorithms.

Please refer to the module guide, for the full syllabus document.
Assessment Details:

This assessment is designed to help develop your understanding of digital signal processing and the use of MATLAB. Provide suitable background information, to support your answers.

1. Given the following plot in Fig Q1. Deduce the equation for  and hence verify using MATLAB.

                                           Fig Q1 Signal Plot                                                             [`10 Marks]
                                                    
2. Given the following continuous time signal:
                                            
                                        

a) Calculate the frequencies contained in the signal. Show all working and provide any background information you feel relevant.#p#分頁標題#e#
b) Write a m-file including the subplot command to plot each frequency and   Be sure to include suitable comments as part of your m-file.
c) Using a suitable sample frequency but 50 sample points, write a m-file to plot the fft of the signal x(t). Discuss any limitations of the algorithms or methods that you have employed to write your program(s).

                                                                                                                         [20 Marks]

3.  Write a suitable m-file to plot the following discrete signal,

       An exponential signal  , is sampled at frequency of 10Hz, beginning at time t=0. 
      Note the sequence generated will be of differing length, so you will need to ensure that the 
      lengths are the same. Write a suitable m file to prove the following.

a) Plot the sampled sequence,  , up to the fifth term.
b) Plot a delayed sequence by 0.2 seconds.
c) Plot the sequence a)+b)

                                                                                                                         [10 Marks]

4. Design a simple lowpass FIR filter using the sinc function and the Hamming window.

a) Write an m-file to create a signal consisting of three frequencies f1=1900Hz, f2=5100Hz and f3 = 7000Hz. 
                                                                                                                          #p#分頁標題#e#
b) Stating any assumptions and showing all working out, design a lowpass filter, to recover f1. Optimize your filter coefficients using the Hamming window.
                                                                                                                        
c) Using the convolution command in Matlab, convolute the signal created in Q4 (a) with the impulse response Q4 (b).  Confirm that the f1 has been recovered. Design the same filter using sptool, and hence discuss any advantages and/or any disadvantages of the use of sptool in digital filter design? Explain how you would import your signal and filter coefficients to the Texas TMS320C5510 DSK.
                                                                                                                           [50 Marks]
5. Report structure and style                                                                                       [10 Marks]

                                                                                                                                      #p#分頁標題#e#

Table of Assessment Criteria and Associated Grading Criteria

Assessment
Criteria
? 
Q1 
Q1 
Q 2 
Q4 
Q5
Weighting: 10% 20% 10% 50% 10%
Grading
Criteria

0 – 29% No evidence of understanding or using the use of Matlab. No Signal plot. No evidence of understanding or using the use of Matlab. No Signal plot. No evidence of understanding or using the use of Matlab. No Signal plot. No evidence of understanding or using the use of Matlab. No Signal plot. Unacceptable in terms of style, language & referencing. Report is not complete.
30 – 39% Little evidence of understanding. In correct signal plot. Little evidence of understanding. In correct signal plot. Little evidence of understanding. In correct signal plot. Little evidence of understanding. In correct signal plot. Major deficiencies in style and language. Questionable attribution of sources.
40 – 49% Signals are generated with appropriate plotting but with some minor errors. Some comments. Little background information provide. Signals are generated with appropriate plotting but with some minor errors. Some comments. Little background information provide. Signals are generated with appropriate plotting but with some minor errors. Some comments .Little background information provide. Signals are generated with appropriate plotting but with some minor errors. Some comments. Little background information provide. Significant shortcomings in style and language.
Attempts at attribution of sources. Use of Harvard referencing.
50 – 59% Signals are generated with appropriate plotting. Background information given. Good use of comments. Background information provided. Signals are generated with appropriate plotting. Background information given. Good use of comments. Background information provided. Signals are generated with appropriate plotting. Background information given. Good use of comments. Background information provided. Signals are generated with appropriate plotting. Background information given. Good use of comments. Background information provided. Style and language generally clear. Some minor errors. 
All sources referenced.   Use of Harvard referencing
60 – 69%
 Signals are generated with appropriate plotting. Good Background information given. Good use of  comments Signals are generated with appropriate plotting. Good Background information given. Good use of  comments Signals are generated with appropriate plotting. Good Background information given. Good use of  comments Signals are generated with appropriate plotting. Good Background information given. Good use of  comments No major shortcomings in style and language.#p#分頁標題#e#
Appropriate referencing. Well structured  Use of Harvard referencing
70+%
 Excellent demonstration use of MATLAB programming, with comprehensive discussion. Excellent demonstration use of MATLAB programming, with comprehensive discussion. Excellent demonstration use of MATLAB programming, with comprehensive discussion. Excellent demonstration use of MATLAB programming, with comprehensive discussion. Clear, logical and error-free. Comprehensive bibliography. All sources appropriately referenced. Use of Harvard referencing